混菌矿化增强再生粗骨料的物理力学性能

为克服单一微生物培养成本高且矿化鲁棒性不足的缺陷，提出了一种混菌矿化增强再生粗骨料物理力学性能的方法.通过筛选矿化效率较高的好氧嗜碱混菌，考察了混菌矿化对再生粗骨料物理力学性能和混凝土抗压强度的影响.结果表明：相同增强时间下，混菌比纯菌呈现出更优异的矿化增强效果；随着混菌矿化增强时间的延长，再生粗骨料吸水率和压碎指标呈现出先减小后增大的趋势，最优增强时间为15 d；采用矿化增强再生粗骨料制备的再生混凝土抗压强度提高幅度达到22.1%.     

Analytical modeling of complex contact behavior between rock mass and lining structure

Based on the nondestructive test data of operating railway tunnels in China, this paper summarizes the basic characteristics of the complex contact behavior between the rock mass and lining structure. The contact modes are classified into dense contact, local non-contact, and loose contact. Subsequently, the corresponding mechanical model for each contact mode is developed according to its mechanical characteristics using the complex variable method. In the proposed mechanical model, a special algorithm is introduced to detect whether the local non-contact zone is re-contacted. Besides, a novel conformal mapping method is also proposed to accurately calculate the mechanical response of the concrete lining. Finally, the accuracy of the proposed method is verified by comparing it with the finite element method (FEM). Several parameter investigations are conducted to analyze the effects of different contact modes on the rock–lining interaction. The results show that: (i) the height of the local non-contact area does not have a significant effect on the contact stress distribution if no re-contact occurs; (ii) backfill grouting can reduce the local stress concentration caused by poor contact modes; and (iii) reducing the friction coefficient of the interface can lead to a more uniform distribution of internal forces in the concrete lining.     

Sustainable phenolic thermosets coatings derived from urushiol

The over-exploitation of finite fossil resources and/or the increased environmental and sustainable awareness inspire scientists and technologists to search for inexpensive alternatives from renewable chemicals. Phenol formaldehyde (PF) resins, the oldest type of synthetic polymers with good mechanical properties and heat resistance, are widely used in the production of coatings, laminates, molding compositions, and glues. Here, biobased urushiol-derived PF resins were synthesized from the alkali-catalyzed reaction between urushiol and formaldehyde. The chemical compositions and molecular structures of resole resins were characterized by carbon-13 nuclear magnetic resonance and Fourier transform infrared spectroscopy, and their curing behaviors were studied by differential scanning calorimetry. The as-prepared urushiol-derived resole resins had methylol (Ph−CH₂OH), ortho- and para-hemiformal groups (Ph−CH₂OCH₂OH), and the para−para/ortho−para/ortho−ortho links of methylene groups (Ph−CH₂−Ph), whereas the resole resins had low curing temperatures at about 100–113°C. Additionally, given the long side alkyl group moiety on the aromatic rings of urushiol, the films of cured urushiol-derived resole resins had low glass transition temperatures of 132 ± 2°C. Furthermore, the as-prepared urushiol-derived coatings exhibited excellent physical and mechanical properties.     

Manipulation of thick-walled PEEK bushing crystallinity and modulus via instrumented compression molding

An instrumented hot compression molding apparatus was fabricated to allow real-time monitoring and precise temperature control during the compaction and consolidation of large polyether ether ketone (PEEK) products. The objective was to determine the impact of controlled variables on the properties of the molded article. Four different strategies were designed to control the mold thermal profiles. The average crystallinity in a commercial molding process is restricted due to large thermal masses with low thermal conductivity. In contrast, this research was able to reduce the crystallinity range from 33% to 6% by developing a special controlled apparatus and implementing new processing methodologies. In this study, PEEK showed a significant increase in the modulus compared to typical values measured on commercially produced analogs, and a higher degree of property uniformity. In a single commercially molded PEEK billet, compressive modulus variability was 13% at room temperature, and 21% at 225°C. Properties of billets produced using the laboratory apparatus showed a reduction in variability to 2%.     

Crushing behavior of alumina inclusions with different porosity during hot compression

Alumina inclusions in commercial as-cast 2.25Cr1Mo0.25V aluminum deoxidized steel exhibited a feature of porous structure. In order to investigate the crushing characteristics of alumina inclusion during hot working, a series of alumina blocks with different porosity whose properties are similar to the alumina inclusions in ingots were prepared using spark plasma sintering. The crushing behavior of alumina blocks during hot compression with quasi-static load was studied. A prediction model of compressive strength of alumina inclusions considering apparent porosity was established on basis of hyperbolic sine Arrhenius equation. A novel crushing mode diagram for alumina inclusions characterized by Z parameter was proposed. The crushing mechanism of alumina inclusions under different deformation parameters was clarified by fracture characteristics. The results showed that the hot compression process of alumina presented a typical brittle fracture, the compressive strength was more sensitive to deformation conditions at lower apparent porosity as compared with the conditions of higher apparent porosity. With the increase of Z, the crushing mode of alumina inclusions gradually changed from intergranular fracture to transgranular fracture.     

Interfacial interactions and properties of cellular structured polyurethane nanocomposite based on carbonaceous nano-fillers

In this article, we have studied the effect of carbonaceous nanofillers viz. fullerenol (0D), carboxylated multi-wall carbon nanotube (MWCNT, 1D), hydroxylated graphene (2D) and combination of carboxylated CNT and hydroxylated graphene as 3D in thermoplastic polyurethane on the tensile properties of the fabricated cellular structures. The concentration of nano-fillers was varied as 0.1, 1, and 5 wt%. Tensile properties of the nanocomposite cellular structures were measured as per ASTM D882 at 20°C (below glass transition temperature, T_g) and 40°C (above T_g). The results have shown that the tensile strength was found to increase by 200%–300% and the tensile modulus was found to increase by 150%–300% for 2D and 3D nano-fillers while significantly poor results were observed for 0D. However, the test data tensile strength and modulus showed marginal increase at 20°C and marginally low at 40°C for 1D filler. The interfacial adhesion was calculated by using experimental tensile data and the predictive models. The interfacial adhesion parameter (B_σ) calculated using Pukanszky equation was found significantly higher value for 2D (B_σ20 = 195.8) and 3D (B_σ20 = 192.0) fillers while poor adhesion was observed for 0D (B_σ20 = −81.6) fillers. The developed cellular structured materials were also evaluated by attenuated total reflection Fourier transform IR spectra, differential scanning calorimetry, X-ray diffraction, scanning electron microscope, and transmission electron microscope.     

Impact of preheating on the mechanical performance of different MgO–C bricks - Low temperature range

This work complements an initial study regarding the mechanical behavior of MgO–C bricks at 1000 °C. In this case, two bricks bonded with phenolic resin, one of them containing aluminum, were treated at 600 °C and mechanically tested at RT and 600 °C. The thermal treatments attempt to simulate the in-service steelmaking ladle preheating process. At low temperatures, the binder pyrolysis is one of the main transformations and the Al melting neither its chemical reactions occur on a large scale yet. To evaluate the effects as the pyrolysis progresses, the soaking time at 600 °C was varied from 1 to 3 h. Although without significant chemical activity, the presence of Al affected the mechanical behavior of the tested bricks. The consolidation of the C–C network coming from the binder pyrolysis was identified as the main factor responsible for counterbalancing the material's degradation by microcracking. The heating combined with the low compressive pre-load applied on the tested specimens appears to close the microcracks and pores.     

Leucokinins: Multifunctional Neuropeptides and Hormones in Insects and Other Invertebrates

Leucokinins (LKs) constitute a neuropeptide family first discovered in a cockroach and later identified in numerous insects and several other invertebrates. The LK receptors are only distantly related to other known receptors. Among insects, there are many examples of species where genes encoding LKs and their receptors are absent. Furthermore, genomics has revealed that LK signaling is lacking in several of the invertebrate phyla and in vertebrates. In insects, the number and complexity of LK-expressing neurons vary, from the simple pattern in the Drosophila larva where the entire CNS has 20 neurons of 3 main types, to cockroaches with about 250 neurons of many different types. Common to all studied insects is the presence or 1–3 pairs of LK-expressing neurosecretory cells in each abdominal neuromere of the ventral nerve cord, that, at least in some insects, regulate secretion in Malpighian tubules. This review summarizes the diverse functional roles of LK signaling in insects, as well as other arthropods and mollusks. These functions include regulation of ion and water homeostasis, feeding, sleep–metabolism interactions, state-dependent memory formation, as well as modulation of gustatory sensitivity and nociception. Other functions are implied by the neuronal distribution of LK, but remain to be investigated.